This is a combined synopsis / solicitation for commercial items prepared in  accordance with the format in far Subpart 12.6, as supplemented with  additional information included in this notice. This procurement is not a  small business set-aside; any responsible source may submit an offer. This  announcement constitutes the only solicitation; proposals are being requested  and a separate written solicitation will not be issued. Solicitation number  M67400-08-t-0092 applies and is issued as a Request for Quotation. This  solicitation document and incorporated provisions and clauses are those in  effect through Federal Acquisition Circular 2005-13 and Defense Acquisition  Circular 91-13. The naics code is 423610. The agency need is for: item no  supplies/services quantity unit unit price 0001   1 Each transformer ffp pad-mounted;  three-phase, nema C57.12.26 and as specified herein, liquid insulated (no  pcb's by jegs requirements, see 6 below), 45 kVA, 13,800 v delta pri. (95 kV  bil), dead front, radial feed, 208 y/120 v sec. 1. Compartments: a. The high  and low-voltage compartments shall be separated by steel isolating barriers  extending the full height and depth of the compartments. B. Compartment  doors: hinged lift-off type with stop in open position and three-point  latching. 2. High voltage: a. 15 kV-200 a bushing wells. B. 15 kV-200 a  loadbreak inserts (ieee std. 386). C. 15 kV-200 a oil-immersed loadbreak  switch. D. Bayonet type, oil-immersed, expulsion fuses in series with oil- immersed, partial-range, current-limiting fuses. Coordinate transformer  protection with expulsion fuse clearing low-current faults and current- limiting fuse clearing high-current faults beyond the interrupting rating of  the expulsion fuse. E. Parking stands. F. Ground pad. 3. Low voltage: a.  Bushings with nema 4-hole spade terminals. B. Accessories: drain valve with  sampler, fill plug, pressure relief device, liquid level gauge, pressure  vacuum gauge and dial type thermometer with maximum temperature indicator. C.  Ground pad. 4. Transformer: a. Liquid insulated, 60 Hz, 65 degrees c rise,  self-cooled type. B. Tap changer shall be externally operated, with four 2.5  percent full capacity taps, two above and two below rated primary voltage. C.  Audible sound level shall be 51 decibels or less. D. Transformer shall  include lifting lugs and provisions for jacking under base. The transformer  base construction shall be suitable for using rollers or skidding in any  direction. Provide transformer top with an access handhole. The transformer  shall have an insulated low-voltage neutral bushing with nema 4-hole spade  terminal, and with removable ground strap. 5. The insulating liquid shall be  less flammable per nfpa 70 and fm P7825, having a fire point not less than 300  degrees c per astm d 92 and dielectric strength not less than 33 kV per astm d  877. The fluid shall be a biodegradable insulating and cooling liquid, ul  classified and fm approved as "less-flammable" fluid, meeting the following  properties: a. Pour point: astm d 97, less than minus 15 degrees c. B.  Aquatic biodegradation: epa 712-c-98-075, 100%. C. Trout toxicity: oecd test  203, zero mortality of epa 600/4-90/027F, pass. 6. Pcb content: the  manufacturer must certify that the transformer does not contain any pcb's.  There is to be no detectable level of pcb's at a detection limit of less than  0.1 (zero point one) ppm. This limit is a jegs (japan environmental governing  standards) requirement that applies to marine corps bases japan. An acceptable  standard test method is astm D4059. 7. Nameplate: ieee C57.12.00 and with "pcb  content data (less than 0.1 ppm)" and "manufacturer's name and type of fluid".  8. Paint base, cabinet and tank munsell 7GY3.29/1.5 green. The paint coating  system shall comply with nema C57.12.29. 9. Routine and other tests (ieee  C57.12.00): cold resistance measurements, phase relation, ratio, no-load  losses and excitation current, load losses and impedance voltage, dielectric  (impulse, applied voltage and induced voltage) and leak. The following is to  be provided along with the offer: 1. Pcb content certification. 2. Outline  drawing of the transformer with devices indicated. 3. Nameplate data. Item no  supplies/services quantity unit unit price 0002   1 Each transformer ffp transformer,  pad-mounted; three-phase, nema C57.12.26 and as specified herein, liquid  insulated (no pcb's by jegs requirements, see 6 below), 500 kVA, 13,800 v  delta pri. (95 kV bil), dead front, radial feed, 208 y/120 v sec. See the long  description. Long description: 1. Compartments: a. The high and low-voltage  compartments shall be separated by steel isolating barriers extending the full  height and depth of the compartments. B. Compartment doors: hinged lift-off  type with stop in open position and three-point latching. 2. High voltage: a.  15 kV-200 a bushing wells. B. 15 kV-200 a loadbreak inserts (ieee std. 386).  C. 15 kV-200 a oil-immersed loadbreak switch. D. Bayonet type, oil-immersed,  expulsion fuses in series with oil-immersed, partial-range, current-limiting  fuses. Coordinate transformer protection with expulsion fuse clearing low- current faults and current-limiting fuse clearing high-current faults beyond  the interrupting rating of the expulsion fuse. E. Parking stands. F. Ground  pad. 3. Low voltage: a. Bushings with nema 10-hole spade terminals. B.  Accessories: drain valve with sampler, fill plug, pressure relief device,  liquid level gauge, pressure vacuum gauge and dial type thermometer with  maximum temperature indicator. C. Ground pad. 4. Transformer: a. Liquid  insulated, 60 Hz, 65 degrees c rise, self-cooled type. B. Tap changer shall  be externally operated, with four 2.5 percent full capacity taps, two above  and two below rated primary voltage. C. Audible sound level shall be 56  decibels or less. D. Transformer shall include lifting lugs and provisions  for jacking under base. The transformer base construction shall be suitable  for using rollers or skidding in any direction. Provide transformer top with  an access handhole. The transformer shall have an insulated low-voltage  neutral bushing with nema 10-hole spade terminal, and with removable ground  strap. 5. The insulating liquid shall be less flammable per nfpa 70 and fm  P7825, having a fire point not less than 300 degrees c per astm d 92 and  dielectric strength not less than 33 kV per astm d 877. The fluid shall be a  biodegradable insulating and cooling liquid, ul classified and fm approved  as "less-flammable" fluid, meeting the following properties: a. Pour point:  astm d 97, less than minus 15 degrees c. B. Aquatic biodegradation: epa 712-c- 98-075, 100%. C. Trout toxicity: oecd test 203, zero mortality of epa 600/4- 90/027F, pass. 6. Pcb content: the manufacturer must certify that the  transformer does not contain any pcb's. There is to be no detectable level of  pcb's at a detection limit of less than 0.1 (zero point one) ppm. This limit  is a jegs (japan environmental governing standards) requirement that applies  to marine corps bases japan. An acceptable standard test method is astm D4059.  7. Nameplate: ieee C57.12.00 and with "pcb content data (less than 0.1 ppm)"  and "manufacturer's name and type of fluid". 8. Paint base, cabinet and tank  munsell 7GY3.29/1.5 green. The paint coating system shall comply with nema  C57.12.29. 9. Routine and other tests (ieee C57.12.00): cold resistance  measurements, phase relation, ratio, no-load losses and excitation current,  load losses and impedance voltage, dielectric (impulse, applied voltage and  induced voltage) and leak. The following is to be provided along with the  offer: 1. Pcb content certification. 2. Outline drawing of the transformer  with devices indicated. 3. Nameplate data. Item no supplies/services  quantity unit unit price 0003 1,000 Feet  cable ffp cable, power, electrical; 15 kv, type "mv-105", ul  listed, # 2, single copper conductor, 220 mil epr insulation (133% insulation  level), extruded conductor shield, extruded insulation shield, copper tape  insulation shield. See the long description. Long description: pvc jacket,  identification on the jacket, # 2 awg size. Southwire CT1-13ET or equal.cable,  power, electrical; 15 kv, type "mv-105", ul listed, # 2, single copper  conductor, 220 mil epr insulation (133% insulation level), extruded conductor  shield, extruded insulation shield, copper tape insulation shield. Item no  supplies/services quantity unit unit price 0004   6 Kit connector elbow ffp  connector, elbow, 200 amp loadbreak , 15KV 1/0 cable item no  supplies/services quantity unit unit price 0005   15 Each terminal lug ffp terminal,  lug; tap, bolted, bronze, sstl. Hardware, up to two cables (two eyebolts) to  3/4" thk flat copper pad, # 1/0 sol.-500 mcm cable size. Item no  supplies/services quantity unit unit price 0006   9 Kit connector elbow ffp connector,  loadbreak elbow kit; 200 a - 15 kV class, w/ test point, individually  packaged, 0.700 - 0.910" insul. Dia., # 1/0 awg str. Or compressed or # 2/0  awg compact conductor. Item no supplies/services quantity unit unit  price 0007 2 Each transformer  ffp transformer, pad-mounted; three-phase, nema C57.12.26 and as specified  herein, liquid insulated (no pcb's by jegs requirements, see 6 below), 112.5  kVA, 13,800 v delta pri. (95 kV bil), dead front, radial feed, 208 y/120 v  sec. See the long description. Long description: 1. Compartments: a. The high  and low-voltage compartments shall be separated by steel isolating barriers  extending the full height and depth of the compartments. B. Compartment  doors: hinged lift-off type with stop in open position and three-point  latching. 2. High voltage: a. 15 kV-200 a bushing wells. B. 15 kV-200 a  loadbreak inserts (ieee std. 386). C. 15 kV-200 a oil-immersed loadbreak  switch. D. Bayonet type, oil-immersed, expulsion fuses in series with oil- immersed, partial-range, current-limiting fuses. Coordinate transformer  protection with expulsion fuse clearing low-current faults and current- limiting fuse clearing high-current faults beyond the interrupting rating of  the expulsion fuse. E. Parking stands. F. Ground pad. 3. Low voltage: a.  Bushings with nema 4-hole spade terminals. B. Accessories: drain valve with  sampler, fill plug, pressure relief device, liquid level gauge, pressure  vacuum gauge and dial type thermometer with maximum temperature indicator. C.  Ground pad. 4. Transformer: a. Liquid insulated, 60 Hz, 65 degrees c rise,  self-cooled type. B. Tap changer shall be externally operated, with four 2.5  percent full capacity taps, two above and two below rated primary voltage. C.  Audible sound level shall be 55 decibels or less. D. Transformer shall  include lifting lugs and provisions for jacking under base. The transformer  base construction shall be suitable for using rollers or skidding in any  direction. Provide transformer top with an access handhole. The transformer  shall have an insulated low-voltage neutral bushing with nema 4-hole spade  terminal, and with removable ground strap. 5. The insulating liquid shall be  less flammable per nfpa 70 and fm P7825, having a fire point not less than 300  degrees c per astm d 92 and dielectric strength not less than 33 kV per astm d  877. The fluid shall be a biodegradable insulating and cooling liquid, ul  classified and fm approved as "less-flammable" fluid, meeting the following  properties: a. Pour point: astm d 97, less than minus 15 degrees c. B.  Aquatic biodegradation: epa 712-c-98-075, 100%. C. Trout toxicity: oecd test  203, zero mortality of epa 600/4-90/027F, pass. 6. Pcb content: the  manufacturer must certify that the transformer does not contain any pcb's.  There is to be no detectable level of pcb's at a detection limit of less than  0.1 (zero point one) ppm. This limit is a jegs (japan environmental governing  standards) requirement that applies to marine corps bases japan. An acceptable  standard test method is astm D4059. 7. Nameplate: ieee C57.12.00 and with "pcb  content data (less than 0.1 ppm)" and "manufacturer's name and type of fluid".  8. Paint base, cabinet and tank munsell 7GY3.29/1.5 green. The paint coating  system shall comply with nema C57.12.29. 9. Routine and other tests (ieee  C57.12.00): cold resistance measurements, phase relation, ratio, no-load  losses and excitation current, load losses and impedance voltage, dielectric  (impulse, applied voltage and induced voltage) and leak. The following is to  be provided along with the offer: 1. Pcb content certification. 2. Outline  drawing of the transformer with devices indicated. 3. Nameplate data. Item no  supplies/services quantity unit unit price 0008   1 Each transformer ffp transformer,  pad-mounted; three-phase, nema C57.12.26 and as specified herein, liquid  insulated (no pcb's by jegs requirements, see 6 below), 225 kVA, 13,800 v  delta pri. (95 kV bil), dead front, radial feed, 208 y/120 v sec. See the long  description. Long description: 1. Compartments: a. The high and low-voltage  compartments shall be separated by steel isolating barriers extending the full  height and depth of the compartments. B. Compartment doors: hinged lift-off  type with stop in open position and three-point latching. 2. High voltage: a.  15 kV-200 a bushing wells. B. 15 kV-200 a loadbreak inserts (ieee std. 386).  C. 15 kV-200 a oil-immersed loadbreak switch. D. Bayonet type, oil-immersed,  expulsion fuses in series with oil-immersed, partial-range, current-limiting  fuses. Coordinate transformer protection with expulsion fuse clearing low- current faults and current-limiting fuse clearing high-current faults beyond  the interrupting rating of the expulsion fuse. E. Parking stands. F. Ground  pad. 3. Low voltage: a. Bushings with nema 6-hole spade terminals. B.  Accessories: drain valve with sampler, fill plug, pressure relief device,  liquid level gauge, pressure vacuum gauge and dial type thermometer with  maximum temperature indicator. C. Ground pad. 4. Transformer: a. Liquid  insulated, 60 Hz, 65 degrees c rise, self-cooled type. B. Tap changer shall  be externally operated, with four 2.5 percent full capacity taps, two above  and two below rated primary voltage. C. Audible sound level shall be 55  decibels or less. D. Transformer shall include lifting lugs and provisions  for jacking under base. The transformer base construction shall be suitable  for using rollers or skidding in any direction. Provide transformer top with  an access handhole. The transformer shall have an insulated low-voltage  neutral bushing with nema 6-hole spade terminal, and with removable ground  strap. 5. The insulating liquid shall be less flammable per nfpa 70 and fm  P7825, having a fire point not less than 300 degrees c per astm d 92 and  dielectric strength not less than 33 kV per astm d 877. The fluid shall be a  biodegradable insulating and cooling liquid, ul classified and fm approved  as "less-flammable" fluid, meeting the following properties: a. Pour point:  astm d 97, less than minus 15 degrees c. B. Aquatic biodegradation: epa 712-c- 98-075, 100%. C. Trout toxicity: oecd test 203, zero mortality of epa 600/4- 90/027F, pass. 6. Pcb content: the manufacturer must certify that the  transformer does not contain any pcb's. There is to be no detectable level of  pcb's at a detection limit of less than 0.1 (zero point one) ppm. This limit  is a jegs (japan environmental governing standards) requirement that applies  to marine corps bases japan. An acceptable standard test method is astm D4059.  7. Nameplate: ieee C57.12.00 and with "pcb content data (less than 0.1 ppm)"  and "manufacturer's name and type of fluid". 8. Paint base, cabinet and tank  munsell 7GY3.29/1.5 green. The paint coating system shall comply with nema  C57.12.29. 9. Routine and other tests (ieee C57.12.00): cold resistance  measurements, phase relation, ratio, no-load losses and excitation current,  load losses and impedance voltage, dielectric (impulse, applied voltage and  induced voltage) and leak. The following is to be provided along with the  offer: 1. Pcb content certification. 2. Outline drawing of the transformer  with devices indicated. 3. Nameplate data. Estimated shipping via ground to:  Defense Logistics Agency Defense Distribution Center Tracy Depot, Bldg 30, ccp  25600 s. Chrisman Rd. Tracy, ca 95376 The Government intends to make a single  award to the responsible offeror whose offer is the most advantageous to the  Government considering technical acceptability, price, and delivery time. The  following Provisions apply to this acquisition: far 52.212-1 Instructions to  Offerors-Commercial Items (Oct 2000), far 52.212-2 Evaluation-Commercial Items  (Jan 1999, applies with paragraph (a) completed as follows: The Government  will award a contract resulting from this solicitation to the responsible  offeror whose offer conforming to the solicitation will be most advantageous  to the Government, price and other factors considered. The following factors  shall be used to evaluate offers: Technical Acceptability, Price, and Delivery  Time, far 52.212-3 Offeror Representations and Certification Commercial Items  (Jun 2003), far 52.212-4 Contract Terms and Conditions Commercial Items (Feb  2002), far 52.212-5 Contract Terms and Conditions Required to Implement  Statutes or Executive Orders ! Commercial Items (Jun 2003), far 52.232-33  Payment by Electronic Funds Transfer (May 1999), far 52.247-34 f.o.b.  Destination (Nov 1991). Responsible offeror must be active in the Central  Contractor Registration on in accordance with dfars 252.204-7004 (nov 2001).  Duns, tin, and cage Code must be written on submitted quote. Payment shall be  made electronically by dfas Yokota Japan. Full text of  http://farsite.hill.af.mil. The following information must be provided with  this quotation: Commercial and government entity code (Cage). Taxpayer  identification number (Tin). Data universal numbering system (Duns).  Estimated Delivery Date: gsa contract number if applicable Remit to Address  Offers can be faxed to 011816117450959, emailed to william.figueroa@usmc.mil,  or mailed to the Regional Contracting Office, psc 557 box 2000, fpo ap 96379- 2000. Offers must be received no later than 14 Feb 2008, 6:00 pm Eastern  Standard Time. Questions may be addressed to Sgt William Figueroa, by email  at:william.figueroa@usmc.mil.